Stainless Steel Joist Hanger (No Bolt Holes)
Overview
Stainless Steel Joist Hangers are pre-punched, formed stainless steel steel connectors available with or without bolt holes and they are very easy to install.
Ideal for:
- Fastening joists to the face of beams.
- Fastening standard trusses to girder trusses.
- Securing beam to beam joints, joists to joists and jacks to TG trusses.
APPLICATION
The Multinail Stainless Steel Joist Hanger is available with or without bolt holes, allowing you flexibility in fastening the Joist Hanger to the truss or beam using nails and/or bolts. Joist Hangers are easy to install. Simply use 5/30mm x 2.8Ø Multinail stainless steel nails, through each wing to secure the Joist Hanger to the supporting member.
Alternatively, use one M12 bolt, with washer, in each wing to secure to the supporting member. To secure the joist to the Joist Hanger, use 3/30mm x 2.8Ø Multinail stainless steel nails through each side.
Multinail Stainless Steel Joist Hanger secured to single girder truss using Multinail stainless steel nails
| Nail fixing schedule | ||
|---|---|---|
| Number of 2.8Ø Nails – Fixing per side | ||
| Nominal Joist Hanger Height (mm) | 90 | 120 |
| Supporting (Girder) Member Fixing | 5 | 6 |
| Carried Member Fixing | 3 | 4 |
LIMIT STATE DESIGN LOADS
The following table gives the recommended Limit State Design capacities for Multinail Stainless Steel Joist Hanger.
Design capacities are for use in limit state design procedures to AS1720.1-2010
NOTE: The capacities are derived from AS1720-2010 and are for uplift in houses where failure is unlikely to affect an area greater than 25m2. For primary elements in structures other than houses or elements in a house for which failure would be greater than 25m2 these capacities must be multiplied by 0.94. For primary joints in essential services or post disaster buildings multiply by 0.88.
| Maximum Limit State Design Capacities (kN) for Joist Hangers | |||||||
|---|---|---|---|---|---|---|---|
| Fixing per side | Load Combination | Joint Group | |||||
| J2 | J3 | J4 | JD3 | JD4 | JD5 | ||
| 5 Nails | Dead Load | 4.5 | 3.2 | 2.3 | 4.5 | 3.2 | 2.6 |
| Dead Load + Floor Live Load | 5.4 | 3.9 | 2.7 | 5.4 | 3.9 | 3.2 | |
| Dead Load + Roof Live Load | 6.1 | 4.4 | 3.1 | 6.1 | 4.4 | 3.6 | |
| 6 Nails | Dead Load | 5.4 | 3.9 | 2.7 | 5.4 | 3.9 | 3.2 |
| Dead Load + Floor Live Load | 6.5 | 4.7 | 3.3 | 6.5 | 4.7 | 3.8 | |
| Dead Load + Roof Live Load | 7.3 | 5.2 | 3.7 | 7.3 | 5.2 | 4.3 | |
| 3 Nails | Dead Load + Wind Load | 5.4 | 3.9 | 2.7 | 5.4 | 3.9 | 3.2 |
| 4 Nails | Dead Load + Wind Load | 7.2 | 5.2 | 3.6 | 7.2 | 5.2 | 4.2 |
* A common joist size in Multinail software is 40×90 joist hanger which uses 5 nails per wing into supporting member and 3 nails each side to carried joist.
The spans in the table have been determined for domestic housing situations with floor live loads of 1.5kPa. The joint group refers to that of the supporting bearer/beam.
| Maximum Span of Floor Joists Supporting Normal Floor Coverings | ||||||
|---|---|---|---|---|---|---|
| No. of nails per wing |
450mm Floor Joist Centres | 600mm Floor Joist Centres | ||||
| JD3/J2 | JD4/J3 | J4 | JD3/J2 | JD4/J3 | J4 | |
| 6 | 7500 | 5400 | 3900 | 6000 | 4300 | 3100 |
DESCRIPTION AND PACKAGING
Manufactured from 0.9mm Minimum Grade 316 Stainless Steel
Stainless Steel Joist Hanger (No Bolt Holes)
| Product Code | Size (W x H) | Carton Quantity | ||
|---|---|---|---|---|
| SJHB35090 | 35 x 90 (35 x 90) | 1 | ||
| SJHB40090 | 40 x 90 (40 x 82) | 1 | ||
| SJHB45090 | 45 x 90 (45 x 80) | 1 | ||
| SJHB50090 | 50 x 90 (50 x 78) | 1 | ||
| SJHB35120 | 35 x 120 (35 x 120) | 1 | ||
| SJHB40120 | 40 x 120 (40 x 120) | 1 | ||
| SJHB45120 | 45 x 120 (45 x 120) | 1 | ||
| SJHB50120 | 50 x 120 (50 x 117) | 1 | ||
| 30mm x 2.8Ø Multinail Stainless Steel Nails (SN30280) | ||||
Personalised. Local. Progressive.